Optical Fiber Composite Overhead Ground Wires (OPGW)
1. General
1.1 This specification covers the requirements of the Optical Fiber
Composite Overhead Ground Wires (OPGW) to be supplied to customer
for use outside installation.
1.2 The optical fiber cable shall comply with the requirements of
this specification and generally meet or better latest standards:
ITU-T G.650: Definitions and test methods for linear, deterministic
attributes of single-mode fiber and cable
ITU-T G.652: Characteristics of a single-mode optical fiber and
cable
ITU-T G.655: Characteristics of a non-zero dispersion-shifted
single-mode optical fiber and cable
IEC 60793-2-50 B1.3: Sectional specification for class B single
mode fibers
IEEE 1138: Standard Construction of Composite Fiber Optic Overhead
Ground Wires (OPGW) for use on Electric Utility Power Lines
ASTM B398: Standard Specification for Aluminum-Alloy 6201-T81 Wire
for Electrical Purposes
ASTM B 415: Standard Specification for Hard-Drawn Aluminum-Clad
Steel Conductors
ASTM B416: Specification for Concentric-Lay-Stranded Aluminum-Clad
Steel Conductors
EIA/TIA-455: Standard Test Procedures for Optic Fibers, Cables,
Transducers, Sensors, Connecting and Terminating Devices and other
Fiber Optic Components
EIA 492A: Generic Specification for Optical Waveguide Fibers
EIA 472A: Sectional Specification for Fiber Optic Communication
Cables for Outside Aerial Use
2. Optical Fiber Characteristics
2.1 The optical, geometrical, mechanical and environment
characteristics of the ITU-T G.652 optical fiber shall be
accordance with below table:
| Characteristics | Specified Values | Units |
| Optical Characteristics |
| Mode field diameter | at 1310nm | 9.1±0.5 | µm |
| at 1550nm | 10.3 ± 0.7 | mm |
| Attenuation coefficient | at 1310nm | ≤0.36 | dB/km |
| at 1550nm | ≤0.22 | dB/km |
| Attenuation non-uniformity | ≤0.05 | dB |
| Zero dispersion wavelength ( λ0) | 1300 ～1324 | nm |
| Max zero dispersion slope (S0max) | ≤0.092 | ps/(nm2·km) |
| Polarization mode dispersion coefficient(PMDQ) | ≤0.2 | |
| Cut-off wavelength (λcc) | ≤1260 | nm |
| Dispersion coefficient | 1288～1339nm | ≤3.5 | ps/(nm·km) |
| 1550nm | ≤18 | ps/(nm·km) |
| Effective group index of refraction (Neff) | at 1310nm | 1.466 | － |
| at 1550nm | 1.467 | － |
| Geometric characteristic |
| Cladding diameter | 125.0±1.0 | µm |
| Cladding non-circularity | ≤1.0 | % |
| Coating diameter | 245.0±10.0 | µm |
| Coating-cladding concentricity error | ≤12.0 | µm |
| Coating non-circularity | ≤6.0 | % |
| Core-cladding concentricity error | ≤0.8 | µm |
| Cladding / coating concentricity error | ≤12.0 | µm |
| Mechanical characteristic |
| Curling | ≥4 | m |
| Proof stress | ≥0.69 | GPa |
| Coating strip force | Average value | 1.0-5.0 | N |
| Peak value | 1.3-8.9 | N |
| Macro bending loss | Ф60mm, 100 circles, at 1550nm | ≤0.05 | dB |
| Ф32mm, 1 circles, at 1550nm | ≤0.05 | dB |
| | | | |
3. Characteristics of Cable
3.1 Cable Construction and Parameter
Overhead ground wire made of aluminum-clad steel wire (AS) and
stainless steel tube containing optical fiber.
3.2Cable type: OPGW-12B1-75[82.8;47.4]
3.2.1 Cross section of OPGW
| Structure | | Material | No. | Material Diameter |
| Fiber | G.652 | 12 | - |
| Center | SUS Tube | 1 | Diameter | 4.0mm |
| Layer 1 | 23%AS wire | 6 | Diameter | 4.0mm |
3.2.1 Specification of OPGW
| Items | Technical Data |
Stranded | Core, layer 1 |
| Stranding direction | Outer layer is right hand |
| Cable diameter (Nominal) | 12.0 mm |
| Cable Weight (Approx.) | 504 kg/km |
| Supporting Cross Section | AS Wire | 75.4 mm2 |
| Rated Tensile Strength (RTS) | 91.0kN |
| Modulus of Elasticity (E-Modulus) | 149.0Gpa |
| Thermal Elongation Coefficient | 12.9×10-6/K |
| Maximum Working Stress (40%RTS ) | 33.12kN |
| Everyday Stress(EDS)(16~25%RTS) | 13.24~20.7kN |
| DC Resistance at 20℃ | 1.008 ohm/km |
| Short time current (1.0s, 40℃～300℃) | 6.9kA |
| Short time current Capacity ( I2t) | 47.4kA²s |
| Minimum bending radius | Installation | 25 times of cable diameter |
| Operation | 15 times of cable diameter |
| Temperature Range | Installation | -10℃～+50℃ |
| Storage & shipping | -40℃～+80℃ |
| Operation | -40℃～+80℃ |
| | | |
4. Fiber and Loose Tube Color Identification
The individual fiber and loose tubes shall accordance with standard
TIA/EIA-598-A and the color code as below.
Fiber Colors
| NO. | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 |
| Color | Blue | Orange | Green | Brown | Grey | White | Red | Nature | Yellow | Violet | Pink | Aqua |
| | | | | | | | | | | | |
5. Mechanical and Environmental Test.
The OPGW cable shall successfully pass the following tests which
don’t must been chosen all. The following test items shall be
carried out in according to corresponding reference.
| No | Item | Reference |
| OPGW tests |
| 1 | Cutoff wavelength | IEEE Std 1138 |
| 2 | Water ingress test | IEEE Std 1138 |
| 3 | Seepage of flooding compound | IEEE Std 1138 |
| 4 | Short circuit test | IEEE Std 1138 |
| 5 | Aeolian vibration test | IEEE Std 1138 |
| 6 | Sheave test | IEEE Std 1138 |
| 7 | Crush test | IEEE Std 1138 |
| 8 | impact test | IEEE Std 1138 |
| 9 | Creep test | IEEE Std 1138 |
| 10 | Stress-strain test | IEEE Std 1138 |
| 11 | Temperature cycling | IEEE Std 1138 |
| 12 | Strain margin test | IEEE Std 1138 |
| 13 | Galloping test | IEEE Std 1138 |
| 14 | Lightning test | IEEE Std 1138 |
| Fiber tests |
| 1 | Attenuation variation with wavelength | IEEE Std 1138 |
| 2 | Attenuation with bending | IEEE Std 1138 |
| 3 | Temperature cycling | IEEE Std 1138 |
| 4 | Attenuation at the water peak | IEEE Std 1138 |
| Field acceptance tests |
| 1 | Fiber continuity | IEEE Std 1138 |
| 2 | Attenuation | IEEE Std 1138 |
| 3 | Fiber length | IEEE Std 1138 |
6. Packing and Shipping
The OPGW shall be tightly and uniformly wound on a strong wood-iron
reel which conforms to ANSI/AA 53-1981 or equal. The reel shall be
lagged with stout wood-iron battens so as to prevent the OPGW from
damage in ordinary shipping, handling, storage and stringing
operations.
FAQ
Q1: Where is your factory ?
A1: Our factory is located in DONGGUAN City, GUANGDONG Province,
China.
Q2: How long has your company been doing this?
A2: More than 20 years.We are not only produce fiber optical cable
but also produce optical fiber and related tools .
Q3:How about the cable's quality?
A4: Our factory is approved by ISO9001 quality management system
and including STARF,CE,CPR,TLC certifications at list.We have a
series of equipment and instruments to make sure reliable quality
of our products.
Q4: Can you produce cable as our requirements?
A6: Of course .We can supply different types of products according
to your requirements with reasonable prices .
Q5:Do you accept the OEM order and how many is the MOQ?
A7:Yes,we warmly welcome your OEM order.To achieve customer's
satisfaction,we accept sample order, even one Piece.
